AZ Barbeque.com

New skillet.

Discussion started on

skou

  • Karma: 0
I was just given a Wagner unmarked 10.5 inch Wagner skillet.

Free!  (My favorite price.)

Neighbor has a friend that runs a storage locker place,
and he gets CI all the time, and doesn't use it.

Frying pan is heavily "seasoned," and has LIGHT rust.
Has 10 1/2 inch and Made in USA on the bottom, a small H
on the bottom of the handle, and a large grunged 8 on the top of
the handle.  This thing's interior is smoother than any Lodge
piece I have, but needs to be burned out and re-seasoned.

steve
#1 - January 22, 2013, 07:13:14 pm
Currently cooking with a newly built UDS,(thanks to Skouson, my brother) which is my current best smoker.  I've also got a Weber Performer, also from Sterling.  My brothers think I'm CRAZY.  (Strangely, they're right.)

Dutch100

  • Karma: 1
Soak in vinegar or Coke overnight to remove the rust
#2 - January 22, 2013, 11:44:30 pm
Mark "Dutch" Wilkins
The Bar B Chuckwagon

Mark

  • Karma: 23
I've iust discovered a couple of old corn stick molds and a flat-bottomed pot that had been semi-protected, collecting dust for decades in a carport. So the steps to rejuvenate are vinegar overnight, burnout in a fire, then grease it up to reseason it and bake it off in the oven?
#3 - January 23, 2013, 06:49:22 am
Mark Motta
Meatier Creator

Dutch100

  • Karma: 1
If light rust, soak in vineger or coke, then scrub/wash and dry. If you want to remove everything, turn it upside down in your home oven and turn on the self-cleaning cycle. When it is done, remove and wipe down with light coat of Crisco. Then bake at 450 degrees for 1 hour, then turn off and allow to cool. Ready to go.
#4 - January 23, 2013, 10:30:51 am
Mark "Dutch" Wilkins
The Bar B Chuckwagon

skou

  • Karma: 0
If light rust, soak in vineger or coke, then scrub/wash and dry. If you want to remove everything, turn it upside down in your home oven and turn on the self-cleaning cycle. When it is done, remove and wipe down with light coat of Crisco. Then bake at 450 degrees for 1 hour, then turn off and allow to cool. Ready to go.


I've found a different method, or oil to season with.

I use walnut or flax seed oil.  Both of them are "drying" oils,
and provide a MUCH more durable surface.  For cooking, I use
whatever tastes appopriate, but for seasoning, I use the above.

After burning off the "seasoning," the light rust came off with
a green scrubby.  The inside looks to be machined, instead of
the rough, pebbly, Lodge surface.

steve
#5 - January 23, 2013, 01:14:54 pm
Currently cooking with a newly built UDS,(thanks to Skouson, my brother) which is my current best smoker.  I've also got a Weber Performer, also from Sterling.  My brothers think I'm CRAZY.  (Strangely, they're right.)

Dutch100

  • Karma: 1
Others have found over time that flaxseed oil will flake and splotch. They have all gone back to Crisco for seasoning.
#6 - January 24, 2013, 09:05:06 am
Mark "Dutch" Wilkins
The Bar B Chuckwagon

skou

  • Karma: 0
I've found a different method, or oil to season with.

I use walnut or flax seed oil.  Both of them are "drying" oils,
and provide a MUCH more durable surface.  For cooking, I use
whatever tastes appopriate, but for seasoning, I use the above.

After burning off the "seasoning," the light rust came off with
a green scrubby.  The inside looks to be machined, instead of
the rough, pebbly, Lodge surface.

steve

Time to update this.

Guys, I've since revised my processes.
I now use walnut or flax oils for woodworking,
and use cooking oils for cooking.  But, it is
corn or soy oil I now use for seasoning.

Yes, the "drying" oils DO flake off, or splotch.
Doesn't give a decent base.  Corn or soy do
much better.  I've been known to use "animal"
oils, sometimes.  On a well-seasoned pan, bacon
works quite well.  Not bacon grease, but bacon.

steve
#7 - October 26, 2014, 12:24:38 am
Currently cooking with a newly built UDS,(thanks to Skouson, my brother) which is my current best smoker.  I've also got a Weber Performer, also from Sterling.  My brothers think I'm CRAZY.  (Strangely, they're right.)

Members:

0 Members and 1 Guest are viewing this topic.